Forum home› Road cycling forum› Your road bikes

Boardman Team carbon

scs-racingscs-racing Posts: 12
edited December 2010 in Your road bikes
One of my first posts after lurking for a while.Thought i would share some photos of my board man,try to follow the photo code but arranging the bike perfectly against the garage door and then taking photos probably made the neighbours think wtf?

Only a few changes from stock really

Ritchey wcs carbon seatpost
Ritchey wcs stem and bars
Specilized toupe team saddle
Continental GP4000S tyres(not shown in photo,spent ages getting the name to line up with valve :twisted: )
cateye strada double wireless(not shown in photo)
Two ebay special carbon cages(£22 for the pair,better than £30-£40 each for branded ones :roll: )

Plus some little bits like white bar tape and red bolts here and there plus some red hudz(not shown in photo)

DSC03346.jpg

DSC03348.jpg

DSC03349.jpg

DSC03345.jpg

DSC03343.jpg

DSC03341.jpg

DSC03340.jpg

Posts

  • Stevo_666Stevo_666 Posts: 44,083
    I rather like that - the bog std Team Carbon is a bit too 'black all over' for my liking (from a pure tart's point of view) :wink:
    Whippet
    Bruiser
    Panzer
    Commuter

    "I spent most of my money on birds, booze and fast cars: the rest of it I just squandered." [George Best]
  • big2000davebig2000dave Posts: 60
    What sized chainring bolts have you used? I got some for my Team Carbon but they were too small! :cry:
    Orange 5 SE
    Santa Cruz Nomad
    Orange 5 Diva
    Boardman Team Carbon
    Bianchi She
  • Ben6899Ben6899 Posts: 8,202
    Are those stem caps used as bar ends? I like your style!
    Ben

    Bikes: Donhou DSS4 Custom | Condor Italia RC | Gios Megalite | Dolan Preffisio | Giant Bowery '76
    Instagram: https://www.instagram.com/ben_h_ppcc/
    Flickr: https://www.flickr.com/photos/[email protected]/
  • scs-racingscs-racing Posts: 12
    big2000dave wrote:
    What sized chainring bolts have you used? I got some for my Team Carbon but they were too small! :cry:

    Not sure on size but these are the ones i bought if that helps

    http://cgi.ebay.co.uk/CHAIN-RING-BOLTS- ... _506wt_911
    Ben6899 wrote:
    Are those stem caps used as bar ends? I like your style!

    Nope there hope bar ends off my old mtb,
  • Ben6899Ben6899 Posts: 8,202
    They look quality, just like stem caps and not like the usual plastic bar end jobs.
    Ben

    Bikes: Donhou DSS4 Custom | Condor Italia RC | Gios Megalite | Dolan Preffisio | Giant Bowery '76
    Instagram: https://www.instagram.com/ben_h_ppcc/
    Flickr: https://www.flickr.com/photos/[email protected]/
  • drkawaszelongdrkawaszelong Posts: 260
    Ha! I've been looking at those carbon bottle cages too! Can they take 1 litre bottles do you know? Or just the 750ml like all the other ridiculously overpriced ones?
    My third
  • Cycling is ForeverCycling is Forever Posts: 210
    Welcome to the club, boardman team carbon club that is
    some nice subtle changes / extras.
    29er http://tinyurl.com/bs4flux
    Dark side http://tinyurl.com/364ow2m
    Old School 26er http://tinyurl.com/2upkwmq
    Hack http://tinyurl.com/36hkmts
  • acidstratoacidstrato Posts: 945
    do the hex bolts in the bar end caps serve a purpose?

    i often lose my bar end caps as my tape pops them out
    Crafted in Italy apparantly
  • scs-racingscs-racing Posts: 12
    Sorry for late reply guys been down in Exmoor for the week.

    Acidstrato the hex bolts are for tightening up a wedge that pushes against the inside of the bar to hold it into place

    DrKawaszelong the cages do take 1l bottles as i tried my lucozade ones in it just to see if they did fit.
  • Time.to.rideTime.to.ride Posts: 463
    The colour coded bolts, end plugs and chainring bolts can also be found at KCNC a really good company that i can fully recommend have purchased loads of parts from there excellant customer service (even Carlos Sastrie appears to be using them on his road bike : see this weeks cycling weekly!) Hope also do these but i find kcnc better , although that is just my opinion. Bike looks the bollocks mate nice to have a change from the standard bike as already said..
  • Time.to.rideTime.to.ride Posts: 463
    big2000dave wrote:
    What sized chainring bolts have you used? I got some for my Team Carbon but they were too small! :cry:

    If you go onto KCNC website then you can see the diff types of everything from bolts to plugs and caps in the three brands sizes campag, shimano and sram and if you want things like chain bolts then look in each page until you see the type of arm you use be it a 4 arm or a five version they are there and there is a contact number if you get stuck!
  • Rynodinio081Rynodinio081 Posts: 122
    I'm thinking of doing the same to my boardman team carbon but with gold instead of red.

    Will it go do you think, I'm a bit hesitant.

    What are the exact names of your bar ends?

    What weight is the bike at now?
  • Rynodinio081Rynodinio081 Posts: 122
    Oh,

    And what size is it to?
Sign In or Register to comment.