Superstar Comp - Switch Ultra converter 10*135 mm alternative?

Lui_DK

Hi folks,
Need some help here. I am looking for the 10*135 thru axle converter for Superstar Components Switch Ultra rear hub: http://www.superstarcomponents.com/en/s ... daptor.htm

But alas! - It's sold out and Superstar Components don't know when its' gonna be back in stock.

So - apparently the switch ultra hub is made by Joy-Tech. Novatec is also made by Joy-Tec, and I hope to find the converter there instead.

Any experience out there? Do you know which Novatec converter to use?

Cheers

-Lui

The Rookie

To clarify, the Superstar hubs are Novatech, its Novatech's cheapest parts that are branded (touch or irony I think) as Joytech.

I have the same hubs, the adaptor is a simple screw in end section.

Lui_DK

Thanks for the swift reply.

The Rookie wrote:

To clarify, the Superstar hubs are Novatech, its Novatech's cheapest parts that are branded (touch or irony I think) as Joytech

OK thx for clarification on that.

The Rookie wrote:

I have the same hubs, the adaptor is a simple screw in end section

Which hubs? SC or Novatec? In case you have the Novatec - which model number is it?

I was wondering if it possible to source the converter at Novatec : http://www.eshop.novatecwheels.eu/categ ... or-d882sb/

poah

you'll be able to find a novatec 4in1 10mm adaptor online (probably from germany or poland)

The rear requires 17mm cone spaners to fit. I had them on Lewis's old wheels.

hubs are 881 front and 882 rear

Lui_DK

Thx a lot!

So what I'm looking for is this: http://www.bdopcycling.com/Wheel%20Part ... D882SB.asp ??

If so, I'll check Germany, Poland, Ebay etc.

The Rookie

I have both the same SS hubs as that and a Novatech 772.

poah

The Rookie wrote:

I have both the same SS hubs as that and a Novatech 772.

772 are not the same as superstar switch ultra hubs.

Lui_DK

Did some more research based on the help given here

http://www.pinkbike.com/forum/listcomme ... did=176301

Apparently Spank Spoon, Octane One Orbital and Sixpack Vice are also made by Novatec.

And Spank Spoon is available in Bike24 http://www.bike24.com/p276746.html

poah

remember you'll need the bolt through QR as well

Lui_DK

POAH wrote:

remember you'll need the bolt through QR as well

Yup - got that all ready

Thanks for the help.

step83

Pretty sure youll need this axle,
http://www.eshop.novatecwheels.eu/categ ... or-d882sb/

Cant seem to see the end cups but i got mine from Superstar im sure. Also SS are out of the 10MM QR's so you may need to get one from somewhere else.

Lui_DK

Step83 wrote:

Pretty sure youll need this axle,
http://www.eshop.novatecwheels.eu/categ ... or-d882sb/

Cant seem to see the end cups but i got mine from Superstar im sure. Also SS are out of the 10MM QR's so you may need to get one from somewhere else.

That's for a traditional QR-skewer. I need the conversion axle (bodyhub) for a 10 mm thru axle QR.

Like this:


Very similar to the 12*142 axle that I got all ready with the Superstar Component wheel set - just slightly smaller in width and internal diameter.

Cheers

-Lui

pastey_boy

I have one, surplus to requirements

The Rookie

POAH wrote:

The Rookie wrote:

I have both the same SS hubs as that and a Novatech 772.

772 are not the same as superstar switch ultra hubs.

I know, didn't say they were, I was saying I have the same Superstar hubs......

steconnor

pastey_boy wrote:

I have one, surplus to requirements

Bit of a thread revival here, don't suppose you still have the surplus 135 x 10 axle?