Fitting Plasma Chain Device...

felix.london
felix.london Posts: 4,067
edited June 2012 in MTB workshop & tech
Anyone know of any instructions online to fitting one of these Superstar chain devices (the ISCG05 version) ?

Thanks.
"Why have that extra tooth if you're not using it?" - Brian Lopes

Votec V.SX Enduro 'Alpine Thug' 2012/2013 build

Trek Session 8

Comments

  • nicklouse
    nicklouse Posts: 50,675
    what bit do you need help with?
    "Do not follow where the path may lead, Go instead where there is no path, and Leave a Trail."
    Parktools :?:SheldonBrown
  • felix.london
    felix.london Posts: 4,067
    It comes with six washers. Where do these go? On the BB shell side of the device, two for each bolt?
    "Why have that extra tooth if you're not using it?" - Brian Lopes

    Votec V.SX Enduro 'Alpine Thug' 2012/2013 build

    Trek Session 8
  • nicklouse
    nicklouse Posts: 50,675
    where ever needed or the bin.

    fit with out and see how it is.
    "Do not follow where the path may lead, Go instead where there is no path, and Leave a Trail."
    Parktools :?:SheldonBrown
  • felix.london
    felix.london Posts: 4,067
    Got it. And as I'm fitting to ISCG - I leave all the spacers on the BB? 2 on drive side, 1 on non-drive side?
    "Why have that extra tooth if you're not using it?" - Brian Lopes

    Votec V.SX Enduro 'Alpine Thug' 2012/2013 build

    Trek Session 8
  • nicklouse
    nicklouse Posts: 50,675
    as it is not BB mount there is no change to the BB.
    "Do not follow where the path may lead, Go instead where there is no path, and Leave a Trail."
    Parktools :?:SheldonBrown
  • stu8975
    stu8975 Posts: 1,334
    If you're fitting (or attempting) to fit it to your Hopper, you have the wrong one as the Hopper doesn't have ISCG tabs on it. And thus you'll need the BB mount version.
  • felix.london
    felix.london Posts: 4,067
    Rockhopper is 2x10 and has a BS Stinger (you couldn't get away with a single ring XC/AM bike over here :wink: )

    It was going on (is on) the NP Snap (with a new BB hence question re. spacers)

    All sorted, looking good & working well 8)

    Like all these things - once you do it once you realise how easy it is. Still not sure about the 6x washers but like nicklous says - it's working so who cares.

    (Snap is looking awesome btw)
    "Why have that extra tooth if you're not using it?" - Brian Lopes

    Votec V.SX Enduro 'Alpine Thug' 2012/2013 build

    Trek Session 8
  • nicklouse
    nicklouse Posts: 50,675
    if they were bolt sized then they can go under the bolt heads, if the body needed moving out from the frame they could go between them. and some times the bolt heads catch on things if you use them.
    "Do not follow where the path may lead, Go instead where there is no path, and Leave a Trail."
    Parktools :?:SheldonBrown
  • felix.london
    felix.london Posts: 4,067
    Yeah, with closer inspection they must be to move the whole device out a bit

    I did put one washer (on each bolt!) in between the frame and device but the chain still sticks slightly proud of the top-guide so reckon another one should help with that
    "Why have that extra tooth if you're not using it?" - Brian Lopes

    Votec V.SX Enduro 'Alpine Thug' 2012/2013 build

    Trek Session 8