Thread To Tell Everyone What Fettling You've Just Done

12467234

Comments

  • Wallace1492
    Wallace1492 Posts: 3,707
    Just changed my pedals thanks to Wiggle delivering to my place of work.
    "Encyclopaedia is a fetish for very small bicycles"
  • chriskempton
    chriskempton Posts: 1,245
    Changed my stem to a slab of Zipp carbon.

    http://www.bikeradar.com/gear/category/ ... stem-11822

    Stiffer honking up hills the result.
  • chriskempton
    chriskempton Posts: 1,245
    Changed my stem to a slab of Zipp carbon.

    http://www.bikeradar.com/gear/category/ ... stem-11822

    Stiffer honking up hills the result.
  • pst88
    pst88 Posts: 621
    Noticed some play in my headset, loosened the stem bolts and tightened the top cap until play went away, retightend the stem bolts and the play came back! Not sure how i've managed that. Maybe I need to tighten the top screw more before I redo the stem bolts? Or something's knackered.

    Next I need to redo my bar tape following a recent crash (involving a broken wrist :cry:)
    Bianchi Via Nirone Veloce/Centaur 2010
  • cjcp
    cjcp Posts: 13,345
    Put new bar tape on (from (ex)white to silvery grey) and reversed/inverted the stem, so it looks a bit more racey. :)
    FCN 2-4.

    "What happens when the hammer goes down, kids?"
    "It stays down, Daddy."
    "Exactly."
  • FeynmanC
    FeynmanC Posts: 649
    I got out the needle and thread to restitch the pockets on my cheapy Aldi shirt.

    That's fettling, right?
    us0.png
  • garmin
    garmin Posts: 31
    Put new bar tape on, new brake blocks,new chain,new cassette and new jockey
    wheels to winter bike. Then did 64 miles to check everything was ok.
    Litespeed Vela
    Dawes giro 400 [winter bike]
    Diamondback S3 full sus

    no pain no gain.
  • Oddjob62
    Oddjob62 Posts: 1,056
    Stuck on my Nitto track drops (B123s) to try them out tomorrow. Might as well start getting used to drop bars before my new bike arrives. Yes that was the most exciting thing i did on this Satruday night :(
    As yet unnamed (Dolan Seta)
    Joelle (Focus Expert SRAM)
  • PinkPedal
    PinkPedal Posts: 180
    Is fettling by proxy allowed? I dropped my bike off at the LBS today for its service and to have one of the handlebar spacers removed :lol:
  • redvee
    redvee Posts: 11,922
    FeynmanC wrote:
    I got out the needle and thread to restitch the pockets on my cheapy Aldi shirt.

    That's fettling, right?

    Got to do the same to a finger on one of my Specialised FF gloves, love them. I did have a pair of hlaf finger(?) gloves but I lost one of the gloves in my Dads shed but found it again but now I've managed to lose one at home somehow :cry:
    I've added a signature to prove it is still possible.
  • itboffin
    itboffin Posts: 20,052
    Replaced the inner tubes on two bikes, then fitted new tires to the CX and Road bikes, took the rear derailleur off my CX and cleaned all the muck off, removed chain and scrubbed silver again, changed battery in cycle computer and reset headset tension on the TT bike.
    Rule #5 // Harden The Feck Up.
    Rule #9 // If you are out riding in bad weather, it means you are a badass. Period.
    Rule #12 // The correct number of bikes to own is n+1.
    Rule #42 // A bike race shall never be preceded with a swim and/or followed by a run.
  • Mills127
    Mills127 Posts: 15
    Finally got sick of a sticky rear brake, took it off the bike, dismantled, degreased and its like new again!

    note: doing this in the garden isn't the best idea - those washers are pretty small and difficult to find on the lawn :roll:
  • FeynmanC
    FeynmanC Posts: 649
    redvee wrote:
    FeynmanC wrote:
    I got out the needle and thread to restitch the pockets on my cheapy Aldi shirt.

    That's fettling, right?

    Got to do the same to a finger on one of my Specialised FF gloves, love them. I did have a pair of hlaf finger(?) gloves but I lost one of the gloves in my Dads shed but found it again but now I've managed to lose one at home somehow :cry:

    When you stitch them up, i'd suggest some elastic through your cycle jersey arms too, so you don't lose them :wink:
    us0.png
  • redvee
    redvee Posts: 11,922
    FeynmanC wrote:
    redvee wrote:
    FeynmanC wrote:
    I got out the needle and thread to restitch the pockets on my cheapy Aldi shirt.

    That's fettling, right?

    Got to do the same to a finger on one of my Specialised FF gloves, love them. I did have a pair of hlaf finger(?) gloves but I lost one of the gloves in my Dads shed but found it again but now I've managed to lose one at home somehow :cry:

    When you stitch them up, i'd suggest some elastic through your cycle jersey arms too, so you don't lose them :wink:

    Knew Mum's idea all those years ago wasn't a stupid one.

    Going to get the babywipes out later before the GP starts and after the Aussie innings finish.

    In wiping the frame found a chainring bolt loose so checked all four of them, luckily just 1/4 were loose.
    I've added a signature to prove it is still possible.
  • prj45
    prj45 Posts: 2,208
    Ohh, didn't realise that this is what this thread was about.

    Well, the other day, for the fist time in nearly 25 years of tinkering with bikes I purchased a chain whip and cassette remover and ... took off my cassette and ... swapped it for another one.

    Now I know how those racer boys get their sprockets so clean.
  • Jamey
    Jamey Posts: 2,152
    Fettled brakes (bit of tightening, bit of side-to-side adjusting)
    Lubed chain and rear mech.
    Pumped tyres.
    Took a test ride down the road.
    Brakes squealing (groaning) again, like after puncture on Friday but cured themselves with about five minutes' worth of riding with the brakes half on.
  • will3
    will3 Posts: 2,173
    Finally got round to fitting a Kona KF front hanger to my Genesis Vapour. Judder seems to have gone and I can apply the brakes with gay abandon. Yay no more scary judder for me with any luck!

    I see the 2010 edition of the vapour has a similar arrangement.
  • biondino
    biondino Posts: 5,990
    pst88 wrote:
    Noticed some play in my headset, loosened the stem bolts and tightened the top cap until play went away, retightend the stem bolts and the play came back! Not sure how i've managed that. Maybe I need to tighten the top screw more before I redo the stem bolts?

    Be careful when you tighten the top screw as it's pre-loaded, so tightening it beyond a certain (not desperately tight-feeling) point will cause it to shear. At least, that's what happened to me :(
  • mudcovered
    mudcovered Posts: 725
    will3 wrote:
    Finally got round to fitting a Kona KF front hanger to my Genesis Vapour. Judder seems to have gone and I can apply the brakes with gay abandon. Yay no more scary judder for me with any luck!

    Just replaced the Avid canti on the front of my Kona with a Kore Race calipers. Way more adjustable and its killed all the judder and squeal issues I was having with the Avid one. Highly recommended to any CX canti user suffering from front brake squeal and fork judder.

    Mike
  • FeynmanC
    FeynmanC Posts: 649
    I just fitted my bright Gelert head torch and a spare rear light off of my mountain bike onto my helmet.

    I think they are on there secure enough but i'll only find out after a ride.

    Only problem is they arent easy to take on and off...so they are on until I get a different solution, or a "day" helmet ;)
    us0.png
  • Roastie
    Roastie Posts: 1,968
    Killboy and I spent the eve bike building. His is 99.9% ready to go (just some small adjustments needed), mine is missing one vital part that halted proceedings at 3:30am.

    Bike shops should open earlier.
  • prj45
    prj45 Posts: 2,208
    Roastie wrote:
    Bike shops should open earlier.

    Or stay open later...
  • itboffin
    itboffin Posts: 20,052
    First ride with my look pedals truely a revelation, spds are fine but don't offer anywhere near the leverage, i'm a convert.

    First ride with my new Ti brakes & Dura Ace cabling mmmm stopping power-tastic

    So far in my quest to go Ceramic & Ti i've dropped 1.5lbs from the weight of my standard Trek 1.7 and considerably more form my wallet :roll:
    Rule #5 // Harden The Feck Up.
    Rule #9 // If you are out riding in bad weather, it means you are a badass. Period.
    Rule #12 // The correct number of bikes to own is n+1.
    Rule #42 // A bike race shall never be preceded with a swim and/or followed by a run.
  • marchant
    marchant Posts: 362
    Some fettling in the future tense; my bottom bracket tool arrived today, and I am anticipating getting the BB itself tomorrow. Wish me luck, this will be the first time I've attempted this job.
  • redvee
    redvee Posts: 11,922
    prj45 wrote:
    Roastie wrote:
    Bike shops should open earlier.

    Or stay open later...

    The only real option, open 24 hours.
    I've added a signature to prove it is still possible.
  • FeynmanC
    FeynmanC Posts: 649
    I've bodged a tesco 3w c battery torch onto my Defy. Elastic bands, small part of an old inner tube, some pipe insulation foam and gaffer tape, plus a couple of strips of masking tape around the batteries to hold them secure in the torch, as they were rattling a little.

    I took it for a ride down an unlit country lane a few minutes ago and it is plenty bright enough to do my country road commute - just have to work out how long the batteries will last and if it's worth getting a recharger and some C size rechargables - anyone got experience of this as i've only ever used AA rechargables before.
    us0.png
  • CiB
    CiB Posts: 6,098
    Thought the chain looked a bit grubby so gave it a wipe, then thought it needed a more thorough clean so split the power link to take it off completely and give it a proper clean & lube, then ended up with the front & rear mechs in a couple of takeaway tubs stripped down to their constituent parts, but at least they were all shiny & clean again by the time I'd finished. And then got the thin brush & Muck-Off round the cassette whilst I was it - so much for a quick wipe of the chain.

    And then re-assemble / refit. Clean gears are better than oily gears.
  • cjcp
    cjcp Posts: 13,345
    Attempted to unseize the front mech on my mtb. Needs more work this morning. More front mech tuning on the commuter too.
    FCN 2-4.

    "What happens when the hammer goes down, kids?"
    "It stays down, Daddy."
    "Exactly."
  • cyberknight
    cyberknight Posts: 1,238
    Lowered the front mech as it was to high and played around with the low stop as since i put the new chain on it occasionally drops off when dropping to the small chain ring.

    Washed and oiled the bike and intend to change the brake pads if i get chance today
    FCN 3/5/9
  • Roastie
    Roastie Posts: 1,968
    prj45 wrote:
    Roastie wrote:
    Bike shops should open earlier.

    Or stay open later...
    Or perhaps open 24/7...